How to Draught-Proof Your Home (and Cut Your Heating Bill)
On this page

How to Draught‑Proof Your Home (and Cut Your Heating Bill)
Spotting the Sneaky Drafts
Before you start taping anything, you need to know where the air is slipping through. A quick way to catch the worst offenders is to grab a lit candle or a thin incense stick and move it slowly around doors, windows, and any gap you can think of. If the flame or smoke wavers, you’ve found a leak.
Another trick is to turn on all the fans in the house, close the doors, and then feel for cold spots with the back of your hand. The colder the spot, the more heat you’re losing.
Quick‑Fix Solutions on a Shoestring
These fixes cost pennies, need only a screwdriver, and can be done in an afternoon.
- Foam tape for windows and doors: Peel‑and‑stick foam weather‑stripping squeezes into the narrow gap between the frame and the sash. It’s cheap, flexible and works well on both wood and u‑PVC.
- Door sweeps: Attach a rubber‑backed sweep to the bottom of any external door. The brush part slides over uneven thresholds while the rubber seals the gap.
- Draft excluders: A rolled towel or a commercial fabric tube can block the space under a door that leads to the garden. If you like a bit of style, you can buy a decorative one for under £10.
- Seal the letterbox: Most letterboxes have a small flap that never closes completely. Slip a thin strip of magnetic tape over the opening when it’s not in use.
- Chimney balloon: If your fireplace isn’t in use, inflate a chimney balloon. It expands to fill the flue and stops cold air from diving straight down the shaft.
Room‑by‑Room Checklist
Once the quick fixes are in place, walk through the house and tackle each room with a short list of tasks. You’ll see that some areas need a little more effort than others.
Living Room
The biggest heat loss usually happens around large windows. If you have double glazing, check the seal between the panes – a tiny bubble means the seal has failed. A cheap replacement sealant can be applied around the outer frame. For single‑glazed windows, consider adding a clear acrylic sheet on the inside; it traps a layer of air and can cut heat loss by up to 30%.
Kitchen
Kitchen doors often sit on worn thresholds. A simple rubber door seal can be pressed into the groove at the bottom of the door. Don’t forget the back of the range hood – a thin strip of aluminium foil can be tucked behind the vent to block drafts while still allowing the fan to pull out steam.
Bathrooms
Exhaust fans are a hidden source of drafts. When the fan isn’t running, the vent cover can let cold air in. Install a self‑closing flap (often called a backdraft damper) that swings shut when the fan stops. It’s a tiny part, but it makes a noticeable difference.
Bedrooms
Under‑floor drafts are common in older homes with timber floorboards. Slip a thin strip of insulation board (about 3 mm thick) under the carpet along the wall edge. If the floor feels squeaky, a little talc powder on the joist side can reduce friction and stop the draft from traveling up.
Basement / Ground‑Floor Rooms
Many houses have air bricks that let the foundation breathe. Never block these; they prevent damp from building up behind the walls. If you notice a draft coming from an air brick, wrap the outside with a breathable mesh and a thin layer of insulation tape – you’ll keep the airflow while reducing the chill.
When to Call in the Pros
DIY works for most gaps, but some areas need a professional’s eye. If you find a cold spot that won’t disappear after you’ve sealed doors, windows, and vents, it could be a hidden crack in the wall or a problem with the loft insulation. A qualified energy‑efficiency assessor can do a blower‑door test, pinpoint the exact leak, and recommend a more permanent fix.
Keeping the Air Flowing Safely
It’s tempting to seal everything up, but you still need fresh air for combustion appliances and to avoid moisture build‑up. Here’s what you should never block:
- Air bricks and vent grilles: They let the building “breathe.” Cover them only with breathable material.
- Gas appliance vents: Any pipe that leads to a boiler, stove, or water heater must stay clear. A blocked vent can cause carbon monoxide to build up.
- Extractor fan ducts: Kitchen and bathroom fans need a clear path to the outside. A damper that closes when the fan stops is fine, but the duct itself must stay open.
If you’re ever unsure, a quick call to a certified installer will save you from a costly mistake.
Wrapping It Up
Getting your home airtight doesn’t have to be a massive project. Start with the cheap, easy fixes, move through each room with a focused checklist, and keep an eye on the places that must stay ventilated. A few dollars and an hour or two of effort can shave a noticeable amount off your heating bill, and you’ll feel the difference the moment you step into a snug, draft‑free living room.
Comments
No comments yet — be the first to share your experience.